Cycle Controls (r3.8)

Cycle Mode Overview

Cycle mode allows control and timing of acquisition sequences. Cycle acquisitions are started when

is enabled and a LOOP acquisition is started.

Cycle acquisitions consist of Iterations each of which is a Loop of 1 or more acquisitions (Loop Repeats) – i.e. a Cycle is effectively a meta-loop, or loop of loops.

At the start of each Cycle Iteration, one or more of the following actions can be specified:

• Wait a specified Iteration Delay before starting Iteration acquisition
• Load a specified Configuration (CFG) file, updating configuration parameters to use for that iteration's acquisition(s)
• Move/step motor to specified coordinates or coordinates associated with specified ROI ID or Position ID
• Update ROI Scan Parameters to those associated with specified ROI ID
• Override Configuration parameters (e.g. # Repeats, # Frames, # Slices, etc) with Iteration-specific values

Left Side Controls

• Unknown macro: {blue}
  : Enables Cycle mode – subsequently started LOOP acquisitions will follow the Cycle parameters configured in this panel.

• Unknown macro: {blue}
  : Name of Cycle file (.CYC), if any, that has last been loaded or saved
• Unknown macro: {blue}
  : Load a Cycle file (.CYC), updating current Cycle parameters.
• Unknown macro: {blue}
  : Save current Cycle parameters to a Cycle file (.CYC). Dialog is launched to select the folder/file to save to.

The current Cycle parameters are exactly those displayed in the

table

• Unknown macro: {blue}
  : On right, sets the number of Cycles to complete before automatically terminating the LOOP acquisition. On left, displays the number of Cycles which have been completed so far. In case of
  Unknown macro: {blue}
  disabled, value at left can be edited to specify which Cycle count value to start with for next started LOOP acquisition.
  • For value > 1, Cycle wraps around to Iteration 1 following the final Iteration N.
  • For value Inf, Cycle wraps around indefinitely and never completes until user hits
    Unknown macro: {blue}
    on the Main Controls panel.

• Unknown macro: {blue}
  : On right, shows the number of Iterations to be executed per-Cycle, i.e. the number defined in the
  Unknown macro: {blue}
  table. On left, displays the number of Iterations which have been completed for the current Cycle count value so far. In case of
  Unknown macro: {blue}
  disabled, value at left can be edited to specify which Iteration to start with for next started LOOP acquisition.

• Unknown macro: {blue}
  : If enabled, the motor position is recorded at start of each Cycle-enabled LOOP acquisition. Upon completion or abort of the acquisition, the motor is moved to restore the starting position.

• Unknown macro: {blue}
  : If enabled, the prevailing Configuration is cached at start of each Cycle-enabled LOOP acquisition – the active settings, not just the settings in the last-loaded Configuration file. Upon completion or abort of the acquisition, the cached Configuration settings are restored.

• Unknown macro: {blue}
  : If enabled, the
  Unknown macro: {blue}
  and
  Unknown macro: {blue}
  values are reset to 0 and 1, respectively, upon completion or abort of each Cycle-enabled LOOP acquisition. If disabled,

Disabling

allows user to handle cases where an ongoing Cycle may need to be aborted/restarted, e.g. for motion or other interruption, perhaps redoing particular iteration(s).

If

is disabled, the following controls are available:

• Unknown macro: {blue}
  : Manually reset the
  Unknown macro: {blue}
  and
  Unknown macro: {blue}
  values to 0 and 1, respectively.

• Unknown macro: {blue}
  : Specifies the number of Cycle iterations to execute before automatically terminating for each started LOOP acquisition. Value of Inf implies to execute all iterations until specified number of Cycles (see
  Unknown macro: {blue}
  ) have completed, if ever.

Setting

to finite value allows one to use

as a 'to-do' list of acquisitions to obtain, one or more at a time.

Right Side Controls

• Unknown macro: {blue}
  : Table specifying number of Cycle Iterations and the actions to implement for each one. Each column is a possible action – leaving a column blank implies that particular action is not taken for that particular Iteration.

• • Unknown macro: {blue}
    : Specify a Configuration (CFG) file to load for that Iteration
  • Unknown macro: {blue}
    : Time, in seconds, to wait before start of this Iteration – the first Repeat, if multiple Repeats are

{blue